If the printer will print but the Ribbon End error stops the printer before the roll is completed or when it gets really low, most of the time it is because of the washers under to end cap on the far right of the spindles that controls the ribbon tension. Fast, accurate and cost-effective Used for: Barcode Printer Thanks for sharing. They contain a small battery in the time chip that keeps the date and time when no power is supplied and can become weak or die out. This is because it just so happens to be the first one to trigger when something mechanically goes wrong.

Uploader: Goltitaxe
Date Added: 5 April 2004
File Size: 48.90 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 3054
Price: Free* [*Free Regsitration Required]

It is so important share new informations about sato cl408e printers Sato cl408e Mario http: Second, check how far left is the sensor assembly, if it is too far to left the edge of the cl40e stock will let light in and will generate a false paper end because the light interferes with sato cl408e voltage reading so it may need to be moved to the right just a little If you still get a Paper End check the voltage setting for the I-Mark sensitively.

Last lock in the adjust nut with the lock screw.

Labels on small bottle Used for: If it hums you may have a bad logic board that drivers the stepper motor or the stepper motor itself is bad. Clinical environments Used for: Sato cl408e you still get ribbon error sato cl408e the lock screw and turn the adjust nut a half turn until the tension is satisfied.

Places with space constraint. Fast Print Speed and Throughput. MB2 Series 2 Inch Label. If you have an Industrial Printer with a sato cl408e look up in the Operators manual on how to bring the I-Mark reading onto the display. You will need to sato cl408e yourself a few questions in order to find out how to fix this error.


How to change to the Direct Thermal Mode will be in the Operators manual. The smaller compacts without displays should be done by a trained technician and not listed in the Operators Manual, only in the Service Manuals. They contain a small battery in the time chip that keeps the sato cl408e and time when no power is supplied and can become weak sato cl408e die out.

If you go to the Service Mode and change it to Yes the Pause will no longer sato cl408e the print job. Sato cl408e called the Reflective sensor in some materials. I recently came to know about http: The ribbon sensor reads the speed of the un -wind supplyand the front re-wind spindle is belt driven so the back spindle simple follows the front. If it don’t move and you now receive a sato cl408e error disable the sensor and this can also be found in the operators manual.

If sato cl408e feeds or will print this means the sensor may need to be cleaned or replaced. If the above suggestions still do not clear the error you may need to do a EPROM clear to unlock all of the old logic and it will be able to calculate again The EPROM clear should also be listed in the manual.


SATO’s industrial-strength printers offer high quality printing even in the harshest environments. There are two washers underneath the cap, one has an align hole that needs to be seated to the ribbon boss The plastic piece sato cl408e cl048e slides onto sato cl408e this ribbon boss has a notch.

This happens to the best of us. I learn something more challenging on different blogs everyday. This error is the most difficult to sato cl408e all with Sato printers.

Highly recommended for satp printing like Sato cl408e Printing, Receipt Printing etc. Watch and listen carefully. This will disable the ribbon sensor long enough to see if it will move because you can’t troubleshoot it until you get it sato cl408e move.

SATO Worldwide | GalleryDriver

Knocks Offline Most of the time this is caused by the Head open or Cover open micro-switches. If you dis-assemble the end of the spindle and inspect the washers you know this is it, because if it is, the align hole will be clogged sato cl408e buildup and you will need to remove the buildup and re-seat it back on the notch and make sure you feel and hear it snap on. High sato cl408e printing on small labels.

There are too many printer menus to list but most always will be in the Service Mode. Fast, accurate and cost-effective Used for: This can verify the correct part sato cl408e replacement. It will always be stimulating to read content from other writers satp practice a little something from their store. SATO’s Mobile printers offers flawless and sato cl408e barcode label printing.


CG4 Series 4Inch Label. Light weight and shock resistance. The models listed above all use the I-Mark sensor to sato cl408e the sato cl408e. If the front supply spindle don’t turn at all, cp408e the side cover to see if the belt is on the ribbon shaft pulley it on correctly.

The Leader in Barcode Printing

Sato cl408e could be the motor pulley is spinning on sato cl408e motor shaft or the pulley is cracked. This is done with a spring. Take the printer offline and press the feed key. This is because it just so happens to be the first one to trigger sato cl408e something mechanically goes wrong. Return to Global Bookmark this Site. Placing a jumper on the connector temporally to one at a time can prove which micro-switch is causing the problem.

Begin typing your search above and press enter to search. Press ESC to cancel.

Back To Top
Show Buttons
Hide Buttons